QSC CX302, CX502, CX702, CX902, CX1102, CX254, CX404, CX204V, CX302V, CX602V, CX1202V User Manual download pdf (Page 13)

Specifications 2- and 4-Channel Distributed 70V Line Models

CX204V CX302V CX602V CX1202V

OUTPUT POWER (Watts)

20 - 20k Hz, 0.03% THD, 70V/Ch. 200 200 400 800

20 - 20k Hz, 0.03% THD, 8 Ohms/Ch. 550 700

20 - 20k Hz, 0.05% THD, 4 Ohms/Ch. 1100

1k Hz, 0.05% THD (EIA), 70V/Ch. 220 250 440 1000

1k Hz, 0.1% THD (EIA), 70V/Ch. 300 600 1200

1k Hz, 1.0% THD (EIA), 70V/Ch. 300

Bridge Mono, 140V, 20 - 20k Hz, 0.1% THD 400 400 800 850

Bridge Mono, 140V, 1k Hz, 0.1% THD 440 600 1200 2400

Bridge Mono, 1k Hz, 0.1% THD, 16 Ohms 1200 1400

Bridge Mono, 1k Hz, 0.1% THD, 8 Ohms 2300

DISTORTION, SMPTE-IM <0.02%, all models

FREQUENCY RESPONSE 20 - 20k Hz, ±0.2dB at 10dB below rated output power, all models (-3dB points: 8 Hz and 100 kHz)

SIGNAL to NOISE, unweighted, 20 - 20k Hz -106 dB. all models

VOLTAGE GAIN 56.6x (35dB) all models

INPUT SENSITIVITY, Vrms 1.26V (+4.2dBu) for rated power at 70.7V

OUTPUT CIRCUIT TYPE AB AB AB H

INPUT IMPEDANCE 6k ohms unbalanced, 12k ohms balanced, all models

DYNAMIC HEADROOM 2 dB at 4 Ohms, all models

DAMPING FACTOR >500 at 8 Ohms, all models

AMPLIFIER PROTECTION Short circuit, open circuit, thermal, ultrasonic and RF protection. Stable into reactive or

mismatched loads

COOLING Continuously variable speed fan; back-to-front air flow through heat sink tunnel

CONTROLS Front: AC POWER switch, gain controls (1 control per channel, 21 detents)

Back: 10-position DIP switch with Clip Limiter (1 per Ch.), LF Filter on/off (1 per Ch.)

LF filter select: 33 or 50 Hz (1 per Ch.), Stereo/Parallel/Bridge mode selection switches

LED INDICATORS POWER (green, 1 each), SIGNAL, -10dB, -20dB (green, 1 each per Ch.), CLIP (red, 1 each per

channel), BRDG and PAR (yellow, 1 each)

CONNECTORS Input: 3-pin terminal blocks ("euro" or "Phoenix" type)and XLRs (pin 2 positive)

Output: barrier strip connectors with protective shroud

Other: QSC DataPort connector (supports full “V1”feature set)

LOAD PROTECTION Turn-on/turnoff muting, AC coupling (DC fault blocking), Clip limiting.

POWER REQUIREMENTS Refer to rear panel serial number label. Configured at factory for 100, 120 or 220-240 VAC, 50- 60 Hz.

DIMENSIONS 19.0" (48.3 cm) W, 3.5" (8.9 cm) H, 14" (35.6 cm) D (from front mounting rails, including rear

support ears)

WEIGHT 21 pounds (9.5 kg) net; 27 pounds (12.3 kg) shipping

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 62 63

No comments

QSC CX302, CX502, CX702, CX902, CX1102, CX254, CX404, CX204V, CX302V, CX602V, CX1202V User Manual Page 13