QSC RAVE 522ua Manual

TD-000198-00 rev.A*TD-000198-00*RAVE 522ua8x8 CobraNet Enabled Signal ProcessorHardware Manual

10Example #5 - Two-Wire Interface (separate network hardware):Example #5 is conceptually similar to example #4. The difference here is that separate n

11UnpackingThere are no special unpacking precautions. However, it is recommended you keep the original packing material for reuse in the rare event t

12Computer Requirements & Software InstallationInstalling QSControl.net is easy. All you need to do is choose the folder where the program is to b

13General Information & Configuration MemoriesNetworkThe network should be operable and QSControl.net software should be installed/running on the

14ConnectionsAC Power CordInsert the molded receptacle of the AC power cord into the AC power inlet on the back of the RAVE 522ua. Plug the AC line co

15Relay OutTwo sets of relay contacts are provided, RELAY OUT 1 and RELAY OUT 2. Contacts are floating and rated for 30VDC, 1A. There is one common te

16LED Indicators (continued)QSControl and CobraNet Network Status (Port) Indicators- There are three LEDs on the front and rear panels labeled RX, TX

17LCD Navigation Map Left side buttons have screen dependent functions.This read-only screen is the “out of the box” default display after power up. T

18Getting StartedThis section outlines one of the simpler methods of getting familiar with your RAVE and the QSControl.net software. The goal of this

19Getting Started (continued)17- Select Device, Add Device, from the menu. A new window will open prompting you to name the device. Name it logically,

2IMPORTANT SAFETY PRECAUTIONS & EXPLANATION OF SYMBOLSThe lightning flash with arrowhead symbol within an equilateral triangle is intended to aler

20Operation QSControl PortThe QSControl port operates on a 10BaseT Ethernet network. This port is one of the primary means for connecting QSControl.ne

21Utility/Diagnostic FunctionsSafe Mode SwitchLocation of Safe Mode switch: The front panel has a small access hole on the left side, just left of the

22Utility/Diagnostic Functions (continued)RS-232 Communications Procedure:1) Connect the RS-232 port of the RAVE 522ua to an unused serial port (COM p

23Utility/Diagnostic Functions (continued)Telnet AccessThe RS-232 features can also be accessed via Telnet. The Microsoft Telnet application is a Wind

24Preliminary SpecificationIN OUT THRUDynamic Range (AES-17, -60dB Method, all sensitivities)unweighted >110dB >112dB >108dBA weighted >11

25Preliminary SpecificationRelay Outputs 2 discrete floating relay switch outputsConnector Type 3-pin "Phoenix Style" (a.k.a. "Euro Sty

26Dimensions

QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA©2005 “QSC” and the QSC logo are registered with the U.S. Pa

3Introduction1- Power indicator2- Diagnostic indicator3- Network status indicators4- Signal presence/clip indicators5- Multi-function push buttons6- D

4does not change regardless of the DSP configuration, unless the configuration intentionally adds more delay. The RAVE 522ua also supports the new opt

5Introduction - Networking the RAVE 522uaThe RAVE 522ua has two RJ-45 network connection ports on the rear panel. One port is labeled "QSControl&

6Third, the RAVE 522ua and QSControl.net system are targeted at network switch deployments. The consumer costs of Ethernet switches have continued to

7Example #2 - CobraNet X-over mode:This is the simplest connection you can make between the RAVE 522ua and any of the other RAVE/BASIS models. Use a C

8Example #3 - Single Wire Interface:Here all QSControl.net and CobraNet traffic shares the same single CAT-5 cable between the RAVE 522ua and an unman

9Example #4 - Two-Wire Interface (shared network hardware):This example illustrates the Two-Wire Interface with a managed Ethernet switch. The switch