QSC CM16a Manual Page 20
- Page / 36
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
20
Section 2: Installation- Connections
CONNECTING AUDIO INPUTS AND OUTPUTS:
The audio inputs and outputs of the DSP-3 use 3-pin “Phoenix”-type (Euro-style) terminal block connectors. These connectors allow pre-
wiring of inputs without any soldering and allow for rerouting of audio inputs by simply interchanging connector locations without the need
for any tools. See Appendix for connector manufacturer’s part number reference.
To connect your signal wire to the terminal-block plug- back the screws out
a few turns to open the wire-clamp, carefully insert the conductors into the proper
location, and retighten the clamping screw.
The recommended stripping length for the wires is approximately 6 to 8
mm ( 1/4 to 5/16 inch). When stripping the audio cable, be careful not to nick or
cut the conductor strands. After each conductor has been stripped and dressed,
insert it fully into the connector and tighten the retaining screw. When stranded
wire is used, carefully twist the conductor strands together so that when they are
inserted into the connector assembly, no loose strands short adjacent terminals.
Unbalanced inputs can be used if required. If unbal-
anced audio sources are used, it is preferable to use an
appropriate audio transformer (or other unbalanced-to-bal-
anced “converter”) to provide a balanced input to the DSP-3.
If this is not possible, then it is recommended that the negative
terminal and shield terminal be connected to one another with
a jumper wire.
Balanced connection is recommended for all inputs.
The terminal block inputs on the DSP-3 are electronically
balanced. Balanced input cables are recommended to mini-
mize noise pick up and prevent ground loops.
With the connector oriented as shown at the right, connect the
positive (+) signal wire to the left-most
Inputs- The audio input can be from one of two sources; the front-panel DataPort OR the terminal-block
INPUT connectors. Do not use both sets of inputs at the same time! Use balanced connections
for the lowest possible noise levels and for minimizing the possibility of hum inducing ground loops.
Outputs- The DSP-3’s post-DSP (processed) audio is output to the rear-panel DataPort AND the terminal-
block OUTPUT connectors. The OUTPUT’s can be used for daisy-chaining the processed audio to
additional amplifiers, even when connected to a DataPort-equipped amplifier via the rear-panel DataPort.
- Digital Signal Processor 1
- TABLE OF CONTENTS 3
- Communications 4
- Commission (FCC) 4
- Information 4
- Introduction- Overview 5
- DSP-3 General Use Guidelines 6
- 3 CONNECT THE AUDIO INPUTS 8
- 5 INSTALL THE SOFTWARE 9
- Introduction- Quick Start 10
- FRONT PANEL 12
- REAR PANEL 13
- Output Peak Limiter 14
- Multiple Delays 14
- Introduction- Block Diagram 16
- Technical Overview 17
- Unpacking and Mounting 18
- Installation- Connections 20
- Application Examples 23
- Software Installation 26
- Section 3: Specifications 27
- Appendix- DataPort Pinout 30
- APPLICATION INFORMATION 32
- Configuration->Edit 33
- Main Number (714) 754-6175 34
Related products and manuals for Processors QSC CM16a
Processors QSC RAVE 522ua Manual
(28 pages)
(28 pages)
Processors QSC BASIS 914lz Manual
(28 pages)
(28 pages)
Processors QSC DCP 300 User Manual
(3 pages)
(3 pages)
Processors QSC BASIS 922uz Manual
(28 pages)
(28 pages)
Processors QSC Q-SYS Core 3000 User Manual
(17 pages)
(17 pages)
Processors QSC Q-SYS I/O-22 User Manual
(4 pages)
(4 pages)
Processors QSC BASIS 922az Manual
(28 pages)
(28 pages)
Processors QSC BASIS 902zz User Manual
(4 pages)
(4 pages)
Processors QSC DSP-4 Manual
(24 pages)
(24 pages)
Processors QSC RAVE 522ua User Manual
(3 pages)
(3 pages)
Processors QSC DCP 100 User Manual
(24 pages)
(24 pages)
Processors QSC RAVE 520uz User Manual
(2 pages)
(2 pages)
Samsung UE46C9000SW manuales
Manuales del propietario y guías del usuario para Televisores Samsung UE46C9000SW.
Ofrecemos 1 manuales en pdf Samsung UE46C9000SW para descargar gratis por tipos de documentos: Manual de usuario
Comments to this Manuals