QSC BASIS 922az Manual Page 1

EN1TD-000133-00 rev.BEN*TD-000133-00*BASIS 922az8x8 CobraNet Enabled Control and Monitoring Signal ProcessorHardware Manual

EN10Example #5 - Two-Wire Interface (separate network hardware):Example #5 is conceptually similar to example #4. The difference here is that separate

EN11UnpackingThere are no special unpacking precautions. However, it is recommended you keep the original packing material for reuse in the rare event

EN12Computer Requirements & Software InstallationInstalling QSControl.net is easy. All you need to do is choose the folder where the program is to

EN13General Information & Configuration MemoriesAmplifier SetupThe QSC DataPort-equipped amplifiers connected to the BASIS 922az must have their p

EN14ConnectionsAC Power CordInsert the molded receptacle of the AC power cord into the AC power inlet on the back of the BASIS 922az. Plug the AC line

EN15Monitor Chain connection. See explanation, at left.InOutMonitor ChainThe MONITOR CHAIN connector is a 5-pin terminal block connector. Input and ou

EN16LED Indicators (continued)QSControl and CobraNet Network Status (Port) Indicators- There are two groups of three LEDs on the front and rear panels

EN17LCD Navigation Map (typical) Left side buttons have screen dependent functions.This read-only screen is the “out of the box” default dis-play afte

EN18Getting StartedThis section outlines one of the simpler methods of getting familiar with your BASIS and the QSControl.net software. The goal of th

EN19Getting Started (continued)17- Select Device, Add New Device, from the menu. A new window will open prompting you to name the device. Name it logi

EN2IMPORTANT SAFETY PRECAUTIONS & EXPLANATION OF SYMBOLSThe lightning flash with arrowhead symbol within an equilateral triangle is intended to al

EN20Operation QSControl PortThe QSControl port operates on a 10BaseT Ethernet network. This port is one of the primary means for connecting QSControl.

EN21Utility/Diagnostic FunctionsReset SwitchLocation of reset switch: The front panel has a small access hole on the left side, just left of the Power

EN22Utility/Diagnostic Functions (continued)RS-232 Communications Procedure:1) Connect the RS-232 port of the BASIS 922az to an unused serial port (CO

EN23Utility/Diagnostic Functions (continued)Telnet AccessThe RS-232 features can also be accessed via Telnet. The Microsoft Telnet application is a Wi

EN24Preliminary SpecificationIN OUT THRUDynamic Range (AES-17, -60dB Method, all sensitivities)unweighted >115dB >112dB >110dBA weighted >

EN25Preliminary SpecificationControl Room Foldback MonitoringConnector Type 5-pin "Phoenix Style" (a.k.a. "Euro Style") detachable

Notes:

Notes:

QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA©2003, 2004 “QSC” and the QSC logo are registered with the U

EN3Introduction1- Power indicator2- Diagnostic indicator3- Network status indicators4- Port connection status indicators5- Multi-function push buttons

EN4Unlike other configurable DSP boxes, the intrinsic process-ing latency of the BASIS 922az is both short and fixed at 0.417 milliseconds. When analo

EN5Introduction - Networking the BASIS 922azThe BASIS 922az has two RJ-45 network connection ports on the rear panel. One port is labeled "QSCont

EN6Third, the BASIS 922az and QSControl.net system are targeted at network switch deployments.The consumer costs of Ethernet switches have continued t

EN7Example #2 - CobraNet X-over mode:This is the simplest connection you can make between two BASIS boxes. You use a CAT-5 crossover cable connected b

EN8Example #3 - Single Wire Interface:Here all QSControl and CobraNet traffic shares the same single CAT-5 cable between the BASIS 922az and an unmana

EN9Example #4 - Two-Wire Interface (shared network hardware):This example illustrates the Two-Wire Interface with a managed Ethernet switch. The switc